Do all the software volume stuff inside each output thread, not in the
player thread. This allows one software mixer per output device, and
also allows the user to configure the mixer type (hardware or
software) for each audio output.
This moves the global "mixer_type" setting into the "audio_output"
section, deprecating the "mixer_enabled" flag.
Some clients have visual feedback for "database update is running".
Using the "database" idle event is unreliable, because it is only
emitted when the database was actually modified. This patch adds the
"update" event, which is emitted when the update is started, and again
when the update is finished, disregarding whether it has been
modified.
At the moment mpd doesn't store or restore the current track to/from
its state file when the daemon is stopped/started while in 'stopped'
state. I believe the preferred behaviour would be to store and
restore the current track even when the daemon is in stopped state
when shutting down.
I made a small patch to adapt this behaviour. If you believe this is
not the preferred behaviour, maybe this should be realized as a
configuration option. I'm not sure how to do this, but made a small
comment, where one would have to put the option.
Several users had problems with binding MPD to "localhost". The cause
was duplicate /etc/hosts entries: the resolver library returns
127.0.0.1 twice, and of course, MPD attempts to bind to "both" of
them. This patch makes failures non-fatal, given that at least one
address was bound successfully. This is a workaround; users should
rather fix their /etc/hosts file.
When all audio outputs have been closed due to failures, pause the
playback instead of stopping it. This way, the user may resume
at the current position after the problem has been dealt with.
The "lastfm" input plugin is far from complete, because MPD does not
support nesting playlists yet. The "fluidsynth" decoder plugin
suffers from shortcomings in the libfluidsynth library:
http://www.mail-archive.com/fluid-dev@nongnu.org/msg01099.html
Even if libsamplerate support is enabled, compile the fallback
resampler. When the user specifies the option
"samplerate_converter=internal", it is chosen in favor of
libsamplerate. This may help users with a weak FPU who don't want to
compile a custom MPD from source, because the fallback resampler does
not use floating point operations.
After a seek, wait until enough new chunks are decoded before starting
playback. If this takes too long, send silence chunks to the audio
outputs meanwhile.
This is similar to the MPD 0.14 patch "wait 10 seconds before
reopening a failed device", which only covered open() failures. This
patch adds the same feature for play().
The default values for buffer_time and period_time were both capped by
the hardware limits on practically all chips. The result was a
period_time which was half as big as the buffer_time. On some chips,
this led to lots of underruns when using a high sample rate (192 kHz),
because MPD had very little time to send new samples to ALSA.
A period time which is one fourth of the buffer time turned out to be
much better. If no period_time is configured, see how much
buffer_time the hardware accepts, and try to configure one fourth of
it as period_time, instead of hard-coding the default period_time
value.
This is yet another attempt to provide a solution which is valid for
all sound chips. Using the SND_PCM_NONBLOCK flag also seemed to solve
the underruns, but put a lot more CPU load to MPD.
The lastfm input plugin enables MPD to play lastfm:// URLs. This
plugin is not complete yet: it plays only the first song in the
last.fm playlist, and the playlist parser isn't even implemented
properly.
This is the first patch in a series to enable 32 bit audio samples in
MPD. 32 bit samples are more tricky than 24 bit samples, because the
integer may overflow when you operate on a sample.
The generic sockaddr struct is too small for some addresses. For
accept(), we have to allocate a sockaddr_storage struct on the stack,
which is large enough for all addresses.
Added the uri_remove_auth() library function which strips username
and password from a HTTP URI, and use it in song_print_url(). This
allows you to add HTTP URIs to the playlist including secret username
and password, without disclosing it to all MPD clients.
If mpd.conf specifies a user, and MPD is invoked by exactly this user,
ignore the "user" setting. Don't bother to look up its groups and
don't attempt to change uid, it won't work anyway.
Use delete_directory() for removing sub directories instead of
dirvec_clear(). This ensures that all memory occupied by
subdirectories of deleted directories is freed.
When a directory is deleted, MPD deleted only the directory from the
database; it did not bother to walk the full tree to free all memory
and to remove deleted songs from the playlist. Replace a
dirvec_delete() with delete_directory().
There are a few problems left in this plugin:
- fluidsynth decodes in real time, while MPD prefers to buffer as
quickly as possible; as a workaround, this plugin uses a timer
object to synchronize with real-time playback
- I don't know yet how fluidsynth tells me when the song has ended
- the "soundfont" configuration setting is not yet documented, and it
will likely change soon (in favor of a per-decoder configuration
block)
